Rør, hvis du tør



Re: Rør, hvis du tør -

Indlægaf kvik » 28. jan 2014, 13:51

Reserved..
Beyerdynamic T1 v1 | AKG K240DF | AKG K400 \\ VE Zen 2.0 | Myst Nail 2 | Spiral Ear 3-way Reference
Zigis Trīsstūris | Eufonika H16M
Tento PortaDAC 1866OCUB | Allo Digione Player
kvik

Brugeravatar
 
Indlæg: 4278
Tilmeldt: 28. jul 2011, 01:27
Geografisk sted: Norge

Re: Rør, hvis du tør - iFi Audio

Indlægaf kvik » 28. jan 2014, 15:47

iFi Pro iCan ($1800)

iFi Pro iCan.jpg
iFi Pro iCan.jpg (1.3 MiB) Vist 18197 gange

iFi is proud to present its flagship Professional ‘Pro’ series. The first product in the range is the Pro iCAN – a studio-grade headphone amplifier AND audiophile line-stage. Inside beats ‘two hearts’ as there is are two individual Solid-State and Tube amplification sections – selectable on the go. There is nothing quite like the Pro iCAN; literally.

The Pro iCAN will for many, be used as a top-of-the-line, headphone amplifier that drives anything and everything – from CIEMs through to the most difficult to drive headphone ever made, the AKG K-1000. Further, Gain is adjustable from 0dB/9dB/18dB. The Pro iCAN can output >10V in Single-Ended mode and 20V in Balanced-mode. The 20V mode is equivalent 100W into a 4 Ohm speaker. So the Pro iCAN can drive almost any headphone into very hard-clipping (protection circuitry typically kicks in under such circumstances).

The Pro iCAN has at the core, a Japan Alps motorised rotary volume potentiometer. This is the ‘6-Track’ version with 4 tracks used for a true balanced volume control. This is the litmus test for any amplifier to see if it is truly balanced, or operates internally in single-ended mode. Those using ‘2-Track’ volume controls may offer balanced in and out, but are not true balanced designs. The Pro iCAN however is fully-balanced from beginning to end.

In terms of flexibility, 3 single-ended and 1 balanced inputs and 1 balanced and 1 single-ended output, the Pro iCAN is a full-function audiophile line-stage that is at home in many expensive hi-fi systems. Its user-selectable Solid-State/Tube amplifiers remain and so are 3D Holographic˚ for Speakers and XBass˚ for ultra-fidelity home audio systems.

Compared to high-end headphone amplifiers, the tube stage of the Pro iCAN is different in two-ways. First, we don’t use good-quality 6922s or similar. Instead we use the very best; General Electric 5670 which is the premium variant with a different pinout. Second and just as important is the circuit design. Unlike other headphone amplifiers that have the same circuit and just switch in/out the tube section, the Pro iCAN is the very first of its kind that has two individual input circuits – one tube and one Solid-State. This results in the best sonics of both worlds because the signal path is the shortest and there is no compromise to ‘shoe horn’ the tubes into an already existing solid-state circuit.

The Solid-State amplification section of the Pro iCAN is just as seriously executed as the Tube amplification section. The amplifer audio circuit is a development of iFi’s revolutionary ‘TubeState’ design. It is fully discrete, fully-balanced with either tube or J-FET input switchable, bipolar second stage and MOSFET-buffered bipolar class A Power stage (with Class AB for low impedance headphones at very high levels). The resulting circuit may be best described as ‘tri-brid’ where each device is used to greatest sonic advantage while minimising any drawbacks. Furthermore, the circuit is pure DC coupled to avoid using any sonically-degrading coupling capacitors.

The Pro iCAN employed TDK Japan-made C0G type capacitors and Vishay MELF type thin film resistors. These are complimented by Panasonic Japan-made ECPU Film Capacitors explicitly designed for audio use with extremely low distortion (<0.00001% @ 1V/10kHz). We employed ELNA Japan-made Silmic II capacitors for the power supplies. These use special silk fibre paper for the isolating barrier resulting in decreased odd-order distortion and reduced microphonics/mechanical resonances.

As one can see, the Pro iCAN despite its ‘desktop’ footprint is absolutely chocked full of premium components yet with a 4-layer pcb, has the ultimate topology in signal path layout/grounding. There is just no more ‘real estate’ left to develop. It truly is deserving of the iFi flagship mantle.



Specifications:
• Gain: 0dB, 9dB and 18dB user-selectable
• Frequency Response: 0.5Hz to 500kHz(-3dB)
• Total Harmonic Distortion (THD, Balanced/Single-Ended): Solid-State: ≤0.0015% / ≤0.005%; Tube: ≤0.002% / ≤0.005%; Tube+: ≤0.012% / ≤0.2%
• Signal-to-Noise Ratio (SNR, Balanced/Single-Ended): >147dB(A) / > 137dB(A)
• Output Power (16Ω, Balanced/Single-Ended): >14,000mW / >4,800mW
• Output Voltage (600Ω, Balanced/Single-Ended): >23V / >11.5V
• Input Voltage (Pro iCAN): DC 9V/6.7A – 18V/3.35A
• Input Voltage (iPower Plus): AC 85 – 265V, 50/60Hz
• Power Consumption: ≤ 22W idle, 50W max.
• Dimensions: 213(l) x 192.5(w) x 63.3(h) mm
• Weight: 1.93kg (4.3lbs)
Test conditions:
Gain = 0dB, 0.775V(0dBu) with 300 Ohm load unless stated otherwise
SNR Balanced re 23V, SNR SE re. 11.5V

https://ifi-audio.com/products/pro-ican/



iFi Retro Stereo 50 (Stereo 50 $1600, LS3.5 speakers $810)

iFi Retro Stereo 50.jpg
iFi Retro Stereo 50.jpg (274.46 KiB) Vist 17629 gange

Starting with the Stereo 50, the iFi Retro is a completely new range that has one objective: to include everyone who loves music regardless of age, gender or technology. The Retro Stereo 50 is an all-in-one tube stereo system: from Bluetooth aptx (phone/pad) to High-res digital (computer) to vinyl (turntable). Everyone can bring their music and be able to connect to the Stereo 50 and produce music that simply astounds. There really is nothing like the Retro Stereo 50.

AMR and iFi are renowned for combining classic valve technology with state-of-the-art digital technology such as in the prestigious AMR DP-777 Digital Processor. The Stereo 50 is the latest from a long line of outstanding products. It features 4xEL84X and 2xECF82 tubes with a stunningly advanced ground-up circuit that has DNA from the best of classic amplifiers such as Telefunken, Marantz and Leak. Running primarily in Class A, its 25W+25W is and sounds astonishingly realistic. This all means a sonic performance that reflects the superb design and implementation.

Got headphones? The Stereo 50 with separate 3.5mm and 6.3mm inputs is just for you. Each headphone input has its own dedicated gain and sensitivity to perfectly match high-sensitivity In-Ear-Monitors and low-sensitivity Over-the-Ear headphones respectively. The 6.3mm output pumps out a “turbo-charged” 7,000mW. So even the most demanding of headphones such as the HiFi Man HE-6 has met its match.

iFi’s iPhono has already become a modern classic and the Stereo 50’s phono stage is set to emulate this feat. It has adjustable ultra-wide gain MM/MC from 38-62dB and its tone control system harks back to classic equalisation technology. With 6 different EQ curves (via the precision tone control), every stereophonic record is catered for. From the default RIAA through to EMI and Decca, as the legion of iPhono users can attest, once dialed-in, each and every record has “a kind of vinyl magic”.

The Stereo 50 “full system” including the Retro LS 3.5 is a match made in audio heaven. The LS3.5 is iFi’s 21st century take on the legendary BBC LS3/5a. To create the LS3.5 speaker, iFi scoured the globe for the very latest technologies and ideal materials. The result is a deep, wide and open sonic signature with spine-tingling tonality.



Specifications
• Wireless Input: Bluetooth (aptX)
• Digital Inputs: USB (DSD512/768kHz/2xDXD), Coaxial (192kHz), Optical (192kHz)
• Analogue Inputs: Line 1, Line 2 (3.5mm share with Line 2), Phono(MM/MC Low/MC High/Line 3)
• Outputs: Loudspeaker Output, Headphone Outputs 3,5mm (imp < 3Ω) & 6.2mm (imp < 6Ω)
• Power output (Music): > 25W(majority Class A)
• Total Harmonic Distortion(THD): < 0.2% (@ 2.83V/1W)
• Output bandwidth: 10Hz ~ 60kHz
• Frequency Response: 10Hz ~ 80kHz
• Signal-to-Noise Ratio : Amplifier >101dB (@ max output), Phono MM >90dB(A), Phono MC >80dB(A)
• DAC Dynamic Range: > 113dB(A)
• Tone Control: Bass(100Hz) +/-8dB, Treble(10KHz) +/-8dB
• Analogue Signal Processing (ASP): XBass, 3D Holographic
• Phono Gain: 38, 50, 62dB
• MM: 220pF//47k
• MC: 200pF//330R
• RIAA Accuracy: <0.5dB
• Tubes: 2 x ECF82; 4 x EL84X
• PCM: 768/705.6/384/352.8/192/176.4/96/88.2/48/44.1kHz
• DSD 512/256/128/64: 24.6/22.6/12.4/11.2/6.2/5.6/3.1/2.8MHz
• DXD: 768/705.6/384/352.8kHz
• Filters: Minimum Phase (PCM 192/176.4/96/88.2/48/44.1kHz), Bit Perfect (DXD/PCM 768/705.6/384/352.8), Analogue (DSD)
• Power Supply: AC 100V-240V
• Power consumption: 75W, ~0.1W (Standard mode)
• Dimensions (W x H x D): 300 x 153 x 226mm
• Weight: 5.8kg


https://ifi-audio.com/products/retro-stereo-50/
Beyerdynamic T1 v1 | AKG K240DF | AKG K400 \\ VE Zen 2.0 | Myst Nail 2 | Spiral Ear 3-way Reference
Zigis Trīsstūris | Eufonika H16M
Tento PortaDAC 1866OCUB | Allo Digione Player
kvik

Brugeravatar
 
Indlæg: 4278
Tilmeldt: 28. jul 2011, 01:27
Geografisk sted: Norge

Re: Rør, hvis du tør - Maverick Audio

Indlægaf kvik » 29. jan 2014, 11:05

Maverick Audio TubeMagic A1 Hybrid Integrated Amplifier ($200)

Maverick Audio TubeMagic A1.jpg
Maverick Audio TubeMagic A1.jpg (27.64 KiB) Vist 18197 gange

Imagine if you could have a power amplifier, a tube headphone amplifier and a tube pre-amplifier all fit within the same small form factor case and built with high-quality “old school” components. Now you can have all of that. This is the Maverick Audio A1 Hybrid Amplifier, a multifunction amplifier that can go anywhere, in any setup and drive your analog listening devices (speakers, headphones) with power and quality.

Audio inputs:
• Analog audio input x 1 (Analog)
• Line-in audio input x 1 (Analog)
• Analog connector: RCA, 1000k ohms

Audio outputs:
• All RCA connectors are gold-plated
• Volume control is provided for all outputs
• Power outputs: 20 watts per channel (into 8 ohms), 40 watts per channel (into 4 ohms)
• Frequency Response: 20Hz – 25KHz
• Input Impedance: 100K ohms
• Analog RCA outputs signal-to-noise ratio: >90dB
• Tube pre-out outputs signal-to-noise ration: >90dB
• Total harmonic distortion: less than 0.1% (Tube pre-out outputs and analog outputs)
• Headphone maximum output power: 1000mW x 2 (32 ohms), 500mW x 2 (300 ohms), 300mW x 2 (600 ohms)

Headphone outputs:
• Standard 1/4″ jack
• Minimum headphone impedance: 16 ohms
• Maximum headphone impedance: 600 ohms
• Headphone output power: 300mW ~ 1000mW

Power:
• R-core Linear 110/220 manual switch

Physical:
• Dimensions: 10″W x 2.1″H x 6.5″D (260mm x 55mm x 167mm)
• Finish: brushed aluminum in black color


http://www.mav-audio.com/base/product/tube_magic_a1
Beyerdynamic T1 v1 | AKG K240DF | AKG K400 \\ VE Zen 2.0 | Myst Nail 2 | Spiral Ear 3-way Reference
Zigis Trīsstūris | Eufonika H16M
Tento PortaDAC 1866OCUB | Allo Digione Player
kvik

Brugeravatar
 
Indlæg: 4278
Tilmeldt: 28. jul 2011, 01:27
Geografisk sted: Norge

Re: Rør, hvis du tør - Icon Audio

Indlægaf kvik » 29. jan 2014, 11:19

Icon Audio HP8 MkII (£950)

Icon Audio HP8 Mk II.jpg
Icon Audio HP8 Mk II.jpg (1.32 MiB) Vist 3918 gange

True High End headphone amplifier. Built as a small SET hi fi amplifier using Icon handmade multi tap output transformers. High definition with superb listening qualities to match the finest headphones.

Headphones have such an intimate relationship with the listener, a good headphone amplifier needs to have the purest possible sound to avoid long term listening fatigue for the user.

The usual way to provide a headphone output on an integrated amplifier is to drop the power through a couple of resistors, giving “low fi” disappointing results. Solid State headphone amps often use a couple of $2 microchips which can sound harsh and have limited power.

We use two Class A valves with high quality output transformers that provide ideal matching to almost any headphone type 30-600.

The power supply has generous mains transformer two custom output transformers. The HP8 MK II is a heavy 7kg, and very solidly made, giving you an idea of how much iron you get for your money!

Like our other models the HP8 MKII has no printed circuit board and is all hand wired with top quality components. We use silver PTFE audio cable, gold plated terminals and the famous “ALPS” volume pot for sonic purity.

The front valve is the excellent ECC83. this has exceptional detail and fluidity. It complements the super 6SN7 (the best hi fi valve ever?). This combination will give you a simply stunning insight into inner detail of your favourite recordings whether analogue or digital.

Like our other amplifiers, close attention has been paid to the finish of the HP8 MKII. It uses the same heavy build quality as our other amplifiers a combination of alloy plate and painted steel.

The HP8 MKII is very versatile. It may connected to your hi fi in several ways:
1, In a normal hi fi system you would connect to the “record out” of your amplifier. This will then be directly connected to the “source” that you have selected.
2, Now with built in loop enabling easy connection.
3, With “Pre and power” systems a connection may be made between the two units.
4, As a stand alone unit you can directly connect to any CD/iphone/phono pre-amp etc.


Specifications and Features
• Comprehensive manual supplied
• All hand wired point to point
• No printed circuit board to ‘colour’ sound
• Japanese Blue ALPS volume pot.
• Class A, all Triode circuit
• Output impedance matching from 6 to 600Ω
• 2 x 6SN7 for output 1x ECC83 input valve
• NOS, Treasure and Full Music types available
• Signal to noise level -90db
• Freq response better than 20hz-20kHz +0 –0.2db
• Total harmonic distortion typically less than 0.2% 1khz
• Also Suitable for ≥ 8 ohm high efficiency loudspeakers
• Japanese steel EI transformers with low oxygen copper
• High quality 2W metal film, & wire-wound resistors
• Solen audio capacitors, capacitor upgrade available
• Custom hand wound output transformers
• Ceramic valve holders for minimum leakage
• Silver PTFE audio cable
• Gold plated Input/outputs
• One line input
• Loop through facility
• 350mv input sensitivity.
• 220/240volts 36 watts.
• 16cm W, 27 D, 16 H, 7kg
• Carton 37Wx27Dx30H 7.0 kg
• C E, ROHS and WEEE compliant
(Specifications subject to change)

https://iconaudio.com/headphone-amplifier-hp8-mkii



Icon Audio HP 205D (£3000)

Icon Audio HP205D.jpg
Icon Audio HP205D.jpg (128.19 KiB) Vist 3918 gange

We believe that Directly Heated Triodes bring you closer to the music!

Many audiophiles have discovered that a simple well designed valve amplifier can give greater purity and intimacy than more complex solid state designs. This is especially true of headphone amplifiers and the 1920s W.E. 205D is about as simple as a valve gets! Taking inspiration from our highly rated HP8 headphone amplifier and the remarkable WE 205D valve, we have designed a deceptively simple amplifier which has surpassed even our own expectations!

The 205D is a Directly Heated Triode designed by the Western Electric Co in the 1920s and is probably the oldest valve in current production! As a small power output valve it has all the right qualities for headphone use, being very linear in operation. High end headphones can be very revealing sounding clinical and overly bright with some amplifiers. Sonic presentation with the 205D and our output transformers has the highest definition and incredible dynamics but in nice way, more vivid and warmer sounding. Completely free of fatigue.

Headphones have the ability to convey incredible detail and insight into a recording so careful circuit design is called for. Like any valve amplifier the output transformers are crucial to the final quality and our own custom designed and wound transformers play an important part in this. Also an advanced design using Directly Heated Triodes such as this demands the highest quality power supplied by outboard power supply using a time honoured valve rectifier and choke circuit.

Although headphones have only a tiny power requirement of no more than one Watt, we have taken the same care and attention to detail that is required with any “high end” design, every component is chosen carefully to avoid negatively influencing the ultimate sound quality. As in our other designs the HP205D is hard wired throughout (without using printed circuit boards) not only for better sound quality by using full size components and easier upgrades but for easy future service.

The 205D is driven by an ECC88 a modern valve which ideally complements the 205D technically and sonically.

The HP205D may be used as a stand-alone unit or as part of a hi fi system. The optional Bluetooth receiver make the HP 205D very versatile in use.


Specifications and Features
• Built in Bluetooth option
• All hand wired point to point
• No printed circuit board to ‘colour’ sound
• Japanese Blue ALPS volume pot.
• Class A, all Triode circuit
• Output impedance matching from 16 to 600Ω
• 2 x 205D for output 2x ECC88 input valve
• Psvane and Full Music upgrade valves available
• Signal to noise level -90db
• Freq response better than 20hz-20kHz +0 –0.2db
• High quality oversize resistors
• SCR audio capacitors, upgrades available
• Custom hand wound output transformers
• Ceramic valve holders for minimum leakage
• Silver PTFE audio cable
• Gold plated Input/outputs
• Loop through facility
• 350mv input sensitivity.
• Comprehensive manual supplied
• 220/240volts 36 watts.
• 16cm W, 27 D, 16 H, 7kg
• Carton 37Wx27Dx30H 7.0 kg
• C E, ROHS and WEEE compliant
(Provisional specifications subject to change)

https://iconaudio.com/hp-205d-headphone ... er-hp-205d



Icon Audio Stereo 20 PP (£950)

Icon Audio Stereo 20 PP.jpg
Icon Audio Stereo 20 PP.jpg (605.7 KiB) Vist 3918 gange

Small But Perfectly Formed! Headphone Socket. Classic Design.15+15 watts. Push-Pull Ultralinear (Triode conversion available). All Triode Driver. Simple Circuit. "Leak" front-end.

In a rapidly changing world it is nice to have some traditional values. In 1955 The British company H. J. Leak designed the Stereo 20 using the new Mullard EL84, and ECC83 valves. It was an instant worldwide success for quality performance and value. These vintage amplifiers can now fetch over £1,500!

Our new Stereo 20pp is inspired by this design. Ideal for the smaller room, or loudspeakers that do not require a large amount of power. Our circuit uses less feedback and designed to be compatible with the higher output that CD players have as well as any almost any other source including DACs and Streaming.

This amplifier has a very transparent quality, being particularly suited to acoustic and orchestral music, but used with appropriate speakers is capable of performance way beyond your expectations!
The inclusion of a dedicated headphone winding on the output transformers guarantees the best possible performance. Giving a closer intimacy than is possible that with solid state headphone amplifiers.

The diminutive EL84 output tube is very efficient much loved power tube, enabling the use of a smaller power supply and output transformers giving economy of size and materials which is reflected in the final price. The EL84 has a very high pedigree having many variants in radio, TV and radar and apparently was even used in the firing mechanism of nuclear missiles!


Specification & Features

• EL84 output valves
• ECC83/ECC82 double triodes valves
• Class A, all Triode front end
• Ultralinear output circuit
• Supplied in triode form upon request (FOC)
• Hand wired point to point components
• 15 Watts per channel Ultralinear
• Suitable for 4 to 8ohm loudspeakers
• Freq response 20-20Khz
• Attractive valve cover included in the price
• Solen hi fi quality audio capacitors
• Silver PTFE audio cable
• Gold plated Input & speaker terminals
• 3 line Inputs for CD, Tuner, MP3 etc
• 250 mv sensitivity for full output
• 220/240volts, 100w
• 27cmW, 30D, 16H cm 10kg
• Comprehensive manual supplied
(Specifications subject to change)

https://iconaudio.com/stereo-20pp-integ ... ereo-20-pp



Icon Audio Stereo 25 Mk II (EL34 £1300, KT88 £1400)

Icon Audio Stereo 25 MkII KT88.jpg
Icon Audio Stereo 25 MkII KT88.jpg (783.61 KiB) Vist 3918 gange

Ideal first valve amplifier with plenty of valve power to drive most loudspeakers!

In essence a simplified ST40 MKIII, yet no reduction in quality, this is our best value integrated amplifier. Features include the excellent 6SN7 and 6SL7 valves for improved sound, and a headphone socket with excellent performance.

Our simple bias circuit means that valve replacement of the same type requires no bias adjustment*. Yet retains the ability to use “tube roll” different valves, so the ST25 MK II is designed to use: 6L6, EL34, 6CA7, KT66, KT88, 6550.

If you are new to valves the Stereo 25 MK II is an excellent starting point. With ample power, its affordable price and excellent power make it an ideal “starter” amplifier to find out what valves can do for your system.

The inclusion of a dedicated headphone winding on the output transformers guarantees the best possible performance. Giving a closer intimacy than is possible that with solid state headphone amplifiers.


Specification & Features
(Typical conditions EL34 [email protected] 240v 50Hz. 8 Ω)
• 6L6/EL34/6CA7/KT66/KT88/6550 output valves
• 6SN7/6SL7 double triode driver valves
• Class A, all Triode front end
• Ultralinear output circuit
• Triode version by request 19+19w (no extra charge)
• Hand wired point to point. No printed circuit board
• 30w RMS per channel Ultralinear (EL34)
• 4 and 8ohm loudspeaker output
• Tertiary Wound Transformers
• Frequency response 20-20khz +0 - 0.5db
• THD typically less 0.5% 1kHz
• Hand wound transformers
• Attractive valve cover included in the price
• Hi Fi quality Solen capacitors
• Silver PTFE audio cable
• Gold plated Input & speaker sockets
• 3 line Inputs for CD, Tuner, Phono etc
• 250 mv input for full output
• 220/240volts, 100w (180w max)
• 34cmW, 34D, 22H (overall) 17kg
• CE, ROHS & WEEE compliant
• Comprehensive manual supplied

*No bias adjustment if the valves are changed for the same type. However bias adjustment and test points are included to get the optimum performance from a wide range of output valves.

https://iconaudio.com/stereo-25-mkii-in ... eo-25-mkii
Beyerdynamic T1 v1 | AKG K240DF | AKG K400 \\ VE Zen 2.0 | Myst Nail 2 | Spiral Ear 3-way Reference
Zigis Trīsstūris | Eufonika H16M
Tento PortaDAC 1866OCUB | Allo Digione Player
kvik

Brugeravatar
 
Indlæg: 4278
Tilmeldt: 28. jul 2011, 01:27
Geografisk sted: Norge

Re: Rør, hvis du tør - Cayin Audio

Indlægaf kvik » 29. jan 2014, 11:21

Cayin Cayin HA-3 ($580)

Cayin Cayin HA-3.jpg
Cayin Cayin HA-3.jpg (242.35 KiB) Vist 18197 gange

The Cayin HA-3 is a DAC coupled to a hybrid headphone amplifier, asymmetrical tubes and MOSFETs in Class A. These tubes are associated with high quality components to deliver a great musicality. HA-3 is equipped with an XMOS asynchronous USB interface, a Burr-Brown PCM1792 converter, an Analog Devices 827JN opamp, and two 6N16B tubes. The amplifier can drive headphones 32-300 Ohm with ease.

Specifications
• Freqency Sesponse: 10Hz-100kHz (AUX input); 10Hz-35kHz (USB input)
• Power Output: [email protected]Ω; [email protected]Ω; [email protected]Ω
• Digital Input: USB Audio (USB 2.0, support upto 24bit/192kHz)
• THD: 0.01% (1kHz)
• S/N: 105dB (A-weighted)
• Input Impedance: 100kOhm (AUX Input)
• Input Sensitivity: 1.8V (AUX Input)
• Input Terminals: USB-B, RCA
• Headphone Output: 6.35mm x2
• Power Consumption: <35W
• Dimensions (WDH): 180x290x65mm
• Net Weight: 3kg
• Tubes: 6N16B x2

http://en.cayin.cn/products_info?itemid=90



Cayin HA-1A mkII ($730)

Cayin HA-1A mkII.jpg
Cayin HA-1A mkII.jpg (92.24 KiB) Vist 18197 gange

Cayin has revamped the highly respected and renowned tube headphone amplifier HA-1A. The extraordinary part of this new amplifier is not only the facelifted wooden appearance, the EL84 based circuit design offers the most natural, realistic and powerful sound of its class and will definitely blow your mind when it sings. HA-1A MK2 will be one of the milestones of Cayin 22 years of expertise and devotion on tube amplification, by using the best possible material, upholding high standards of craftsmanship and dedicating to perfection, it shall reflect the kind of promises that Cayin has been strived for ever since.

FEATURES
• Serious upgrade to the Stereophile recommended HA-1A
• USA NOS Tung-Sol 12DT5 vacuum tube for recitification
• Enhanced S/N ratio and frequency response
• New designed upgraded output transformers
• Three points foundation support design
• Stylish and elegant piano paint finish red wood side benches
• Can also be used as a 14db gain vacuum tube pre amplifier
• 2 x 12AU7 for pre-amplifier stage
• EL84 x 2 vacuum tubes for power output stage
• Silver plated high purity copper internal signal wiring
• Special handmade low magnetic leakage toroidal power transformer
• Special handmade wide frequency response Ei audio transformers
• All point to point wiring (hand soldering)
• Detachable power cord system (IEC)


SPECIFICATIONS
• Tubes: 12AU7 x2, EL84EH x2, 12DT5 x1
• Dimensions (WDH): 126.5x304x215mm
• Net Weight: 9.5kg
• Power Consumption: 65W
• Input Terminial: CD, AUX
• Output Terminal: PRE-OUT

As Headphone Amplifier
• Output Impedance: 8-32Ω, 33-64Ω, 65-150Ω, 151-300Ω, 600Ω
• Power Rating: [email protected]Ω; [email protected]Ω; [email protected]Ω; [email protected]Ω; [email protected]Ω
• Input Sensitivity: 200mV-440mV
• Frequency Response: 20Hz-45kHz ±3dB
• THD: 1% (1KhZ)
• SNR: 100dB (A-weighted)

As Preamplifier
• Output Level: 2V (max 4V)
• Frequency Response: 10Hz-42kHz ±3dB
• Input Sensitvity: 420mV
• THD: 0.5%
• SNR: 100dB

http://en.cayin.cn/products_info?itemid=89

Note: Also sold as Cayin CS-1H



Cayin HA-6A ($2400)

Cayin HA-6A.jpg
Cayin HA-6A.jpg (1.74 MiB) Vist 4001 gange

Available 2020 Q1

HA-6A offers both triode and ultra-linear mode, which can be seleced without turning off the amplifier. The input tubes are 12AU7. The two rectifier tubes on the left are 22DE4. With HA-6A you can swap between EL34 and KT88 anytime you like.. In KT88 mode, you can use KT88 variants including KT100, KT90, 6550, 6550A, 6550EH vacuum tubes. In EL34 mode, you can also use EL37, 6CA7, 6L6GC, 5881, KT77 and KT66. Together with Triode and Ultra-linear dual mode selection, the HA-6A offers a lot of sound signature options in one compact chassis.

The amplifier will be pre-installed with a matched pair of Genalex Gold Lion KT88, and we'll include a matched pair of Electro-Harmonix EL34 EH in the the HA-6A package. In other word, you don't have to choose your prefer power tube, you own both options immediately and you can tube rolling as soon as you finish taking your open-box photo

The HA-6A incurred a lot of elements from HA-300, you can even consider the chassis as a one-box scale-down version of HA-300, with the separated power supply merged with the amplifier chassis and then scaled down from 445mm (159 mm + 286mm in HA-300) to the current 360mm The net weight of HA-6A is 19kg, so the shipping weight will be around 25kg.

The HA-6A has incurred the proven amplification design of our HA-300. The tube amplification part of the HA-6A is single-ended Class A, and then output from Power Tubes will feed into a pair of output transformer to provide genuine balanced driven output (both XLR4 and 4.4mm). The single-ended RCA input will feed into the Tube Amplification section directly, but the Balanced XLR input go through a pair of input transformer and converted to single-ended.

So to clear the doubt. Yes, the EL34 and KT88 are operated in Class A Single-ended, but the XLR4 and 4.4mm are truly balanced driver, they are NOT hard wired from single-ended phone out and they sound very different because of our Transformer coupled design. Will single-ended tube amplification sounds good with balanced headphones? Definitely if you implemented this correctly and Cayin HA-300 sustain this claim. The design and quality of output transformer plays a very vital part in this approach and Cayin has a very unique advantages in this aspect: we are one of the very few, if not the only, headphone amplifier manufacturer that incorporate transformer design and production in-house. We can design the transformers to meet the need of a specific amplifier, and wind the transformer in house exactly as design even when we are making high-end amplifier in small production batch.


HA-6A specs.jpg
HA-6A specs.jpg (316.41 KiB) Vist 4001 gange

https://en.cayin.cn/products_info?itemid=127
https://www.head-fi.org/threads/cayin-h ... 99.918779/



Cayin HA-300 ($4000)

Cayin HA-300.jpg
Cayin HA-300.jpg (855.26 KiB) Vist 15689 gange

The HA-300 adopts the Class A single-end amplification with a balanced output design. The output of the 300B power tube will feed to a pair of output transformers for single-end or balanced output. Being one of the biggest tube amplifier manufacturers in the world, Cayin designs and builds our transformers, making sure even the finest detail will be attended to. In the case of HA-300, the output transformer was specially winded to provide three set of impedance matched outputs at 8-64Ω, 65-250Ω, and 251-600Ω respectively, making it extremely versatile to match with a wide range of headphones in the market.

We also built an outboard power supply for HA-300. On top of the in-house design, custom-build toroidal power transformer, we developed a special circuit to supply steady power independently to different gain stages. The voltage amplifier circuit will adopt an independent regulator design, and we shall deploy 4 pieces of NOS RCA 22DE4 as rectifier tubes. This power supply design will deliver the cleanest power possible with minimal interference to the line signal amplification in the main Amplifier chassis.

On top of a 6.35mm singled-ended and 4-pin XLR balanced headphone output, the HA-300 has a set of speaker outputs so it can be used as a speaker amplifier delivering up to 8wpc Class A output


Features
• Best possible integration of balanced and singled-end signal processing: Input Transformer(for Bal input)-> Push-pull Single-end Amplification-> Output Transformer (for Bal output)
• Two-boxes design with multi-stage tube regulated power supply
• Carefully selected premium tubes
Power Amplification: Full Music gold pins ceramic base 300B x2
Voltage Amplification: Shuguang WE6SN7 replica of Western Electric x2
Tube Rectification: NOS RCA 22DE4 rectifier tubes x4
• In-house design and custom-build power, input and output transformers
• Provide choice of headphone outputs for high, middle and low impedance; make sure all headphones will perform satisfactory.
• Point-to-point Wielding to ensure shortest signal path and enhance the transparency and refinement of audio performance
• High quality shield silver-plated internal cable to minimize interference during transmission
• High-Precision 24 steps potentiometer to provide low noise, high-precision volume control
• US Aviation standard sockets and connectors for outboard power supply connection.
• Beautifully designed and crafted VU meters to monitor the signal level
• LIghtweight aluminium alloy panels, hand-painted finishing for uniform and long lasting high-gloss surface

HA-300_specification.jpg
HA-300_specification.jpg (169.83 KiB) Vist 15689 gange

http://en.cayin.cn/products_info?itemid=112
https://www.head-fi.org/threads/cayin-u ... 18.872093/
Beyerdynamic T1 v1 | AKG K240DF | AKG K400 \\ VE Zen 2.0 | Myst Nail 2 | Spiral Ear 3-way Reference
Zigis Trīsstūris | Eufonika H16M
Tento PortaDAC 1866OCUB | Allo Digione Player
kvik

Brugeravatar
 
Indlæg: 4278
Tilmeldt: 28. jul 2011, 01:27
Geografisk sted: Norge

Re: Rør, hvis du tør - Xindak

Indlægaf kvik » 29. jan 2014, 11:23

Xindak MT-2 Headphone Amplifer / USB DAC ($415)

Xindak MT-2.jpg
Xindak MT-2.jpg (104.13 KiB) Vist 18197 gange

MT-2 is an integrated amplifier adopts tube amplifying and also can use as headphone amplifier. The units appearance is very exquisite and small, which width is only 26cm. The circuit adopts 6P1 vacuum tube as its amplifying tube which form pre-amplifying and drive with 6J1 tube. Adopts Xindak E type special made broadband output transformer, about power supply, it’s adopts 85w high reliability E type power transformer. Besides providing 6.35mm headphone output Jack,it also have USB interface build-in. Trough USB connect cable connect to computer which installed windows system , the device can use as external USB audio DAC. Its voice is clear and transparent, exquisite, mellow, warm and melting. This product have two different version, the one MT-2(II) equipped with the aluminum alloy brushing panel.

• Rated Output Power: 1.5W/4Ω
• Input Sensitivity: 400mV for maximum rated output power
• Frequency Response: 10Hz-20kHz
• Input: RCA*1, USB *1
• S/N Ratio: >83dB
• THD: 1% (1kHz/1V)
• Number of Channels: 2
• Power Consumption: 56W
• Tubes: 6P1*2, 6J1*2
• Net Weight: 5.5Kg
• Dimensions (W*H*D): 260mm*150mm*186mm

http://www.xindak.com/en-us/product_det ... ductID=465


OBS! Also sold as Audreal MT-2 II ($610)
Beyerdynamic T1 v1 | AKG K240DF | AKG K400 \\ VE Zen 2.0 | Myst Nail 2 | Spiral Ear 3-way Reference
Zigis Trīsstūris | Eufonika H16M
Tento PortaDAC 1866OCUB | Allo Digione Player
kvik

Brugeravatar
 
Indlæg: 4278
Tilmeldt: 28. jul 2011, 01:27
Geografisk sted: Norge

Re: Rør, hvis du tør - Audio Space

Indlægaf kvik » 29. jan 2014, 11:36

Audio Space Mini-2 SE (AUD2200)

Audio Space Mini-2 SE.jpg
Audio Space Mini-2 SE.jpg (102.73 KiB) Vist 18197 gange

No, the Audio space Mini-2SE is not a single-ended amplifier, Audio Space does make single-ended amplifiers and better push-pull amplifiers but of course they also cost considerably more money. First, let’s see what you get. Opening the box you get a nicely chrome finished chassis amplifier with point to point internal wiring. Excellent build construction and a nice set of switches and knobs that feel solid. No cheap plastic buttons that adorn almost everything in this price range that make you wonder if you should have just shopped for your hi-fi at Walmart instead. The amplifier offers three switches for maximum and minimum feedback, triode and ultralinear mode, and a direct source switch to allow the integrated to be operated as a power amp. There are three line inputs, no phono stage, and a very good headphone output. There is no remote control. The amplifier certainly provides a high pride of ownership factor in terms of looks and build for this money.

The Mini-2SE is quite a neutral amplifier – solid bass and extended treble. The sound is never thick, or overly veiled or mellifluous. I tried all the various options running the amplifier in ultralinear and triode mode as well as max and minimum feedback. I ultimately found that the amplifier sounded best in triode mode with minimum feedback. For tough-to-drive loudspeakers with rock at higher levels, it is nice to have the ultralinear mode and max feedback mode which effectively doubles the amp’s power. This is a nice option for parties when critical listening isn’t required.

Few amplifiers bother with a headphone amp section and when they do it seems to be a cheap op-amp add on just to advertise that it has one. The Audio Space is a serious tube amp. I own a dedicated Antique Sound Lab MG Head DT as well as a Total Bithead headphone amp and the Audio Space mini-2SE is a significant upgrade to both units. With my HD 600, the Audio Space generated significantly better bass response in terms of depth and drive, and sounded more open and spacious than my other headphone amplifiers. The amplifier was free of noise in either stereo or headphone mode. The amplifier has a hint of softness around the leading edges of notes, which I found preferable to the ultralinear mode where it may perhaps be viewed by some as superior or more accurate but comes across as a little more “glassy.” What is nice about the switches is that they give you the ability to make the subtle adjustments to your preferences and perhaps to tailor the sound to your chosen headphones.


Outstanding Features:
• Rugged stainless steel chassis
• High quality EI transformers and components
• Switching between ultra-linear and triode
• Switching between high and low negative feedback
• Switching between direct and line input
• Headphone jack
• Innovative tube circuitry with choke coil
• Point to point soldering

Specifications
• Input: Single-ended RCA x 3
• Output Impedance: 4, 8 ohm
• Output Power:
24W x 2(Ultralinear - Class AB Push-Pull),
12W x 2 (Triode - Class AB Push-Pull)
• Frequency Response: 15Hz-30KHz +/-1dB
• T.H.D.: < 1%
• Input Sensitivity: 230mV - 300mV
• S/N Ratio: > 87dB
• Channel Balance: < 1dB
• Vacuum Tubes:
1x 6N9P (6SL7 or ECC35)
2x 6N8P (&SN7 or ECC32)
4x EL34 (6CA7)
• Dimension (DxWxH): 345 x 240 x 175 mm
• Weight: 13.2 kg ( N.W.) / 16.5 kg (G.W.)

http://audiospace.com.au/p14/Mini-2SE/p ... 0538c25c55
http://dagogo.com/audio-space-mini-2se- ... ier-review


Other Audio Space tube integrated amplifiers with headphone-out:
AS-2i (AUD1680)
AS-2.8i (AUD1775)
AS 3i (AUD2190)
AS-3.8I (KT88) (AUD2700)
AS 6i (300B) (AUD4780)
AS-6i Pro (AUD3235)
Galaxy 34 (AUD2700)

http://audiospace.com.au/Integrated-Amp ... index.html
http://www.audio-space.com/product-cate ... amplifier/
http://www.charismaaudio.com/?page_id=1015
Beyerdynamic T1 v1 | AKG K240DF | AKG K400 \\ VE Zen 2.0 | Myst Nail 2 | Spiral Ear 3-way Reference
Zigis Trīsstūris | Eufonika H16M
Tento PortaDAC 1866OCUB | Allo Digione Player
kvik

Brugeravatar
 
Indlæg: 4278
Tilmeldt: 28. jul 2011, 01:27
Geografisk sted: Norge

Re: Rør, hvis du tør -

Indlægaf kvik » 29. jan 2014, 14:03

Reserved..
Beyerdynamic T1 v1 | AKG K240DF | AKG K400 \\ VE Zen 2.0 | Myst Nail 2 | Spiral Ear 3-way Reference
Zigis Trīsstūris | Eufonika H16M
Tento PortaDAC 1866OCUB | Allo Digione Player
kvik

Brugeravatar
 
Indlæg: 4278
Tilmeldt: 28. jul 2011, 01:27
Geografisk sted: Norge

Re: Rør, hvis du tør - Estro Armonico

Indlægaf kvik » 29. jan 2014, 14:06

Estro Armonico OTL Headphone Amplifier (€2100)

Estro Armonico_1.jpg
Estro Armonico_1.jpg (95.78 KiB) Vist 3850 gange
Estro Armonico_2.jpg
Estro Armonico_2.jpg (182.97 KiB) Vist 3850 gange

High Performance Edition

Initially a custom amp made only for a little group of people, and though not listed on the website, it is available on-demand by contacting the manufacturer.

For product details see the HeadFi review (link below). The amp can be customized to some degree - no. of inputs, Line-Out/Pre-Out, Caps, ao.

Separate power supply (5U4), weighing a hefty 11 kg

Tube complement: 1x 5U4 / 2x 6H23 / 2x 5998



http://www.estroarmonicoaudio.com/index ... odotti/it/
https://www.facebook.com/pg/Estro-Armon ... 23/photos/
https://www.head-fi.org/threads/review- ... er.785927/
Beyerdynamic T1 v1 | AKG K240DF | AKG K400 \\ VE Zen 2.0 | Myst Nail 2 | Spiral Ear 3-way Reference
Zigis Trīsstūris | Eufonika H16M
Tento PortaDAC 1866OCUB | Allo Digione Player
kvik

Brugeravatar
 
Indlæg: 4278
Tilmeldt: 28. jul 2011, 01:27
Geografisk sted: Norge

Re: Rør, hvis du tør - World Designs

Indlægaf kvik » 30. jan 2014, 23:13

World Designs HD3S (Kit Standard/XL £500/575, Built +£160)

World Designs HD3S.jpg
World Designs HD3S.jpg (129.35 KiB) Vist 18197 gange

A beautifully simple, yet sophisticated, stereo headphone amplifier design using ECL83 valves. The unit works directly from any source and includes headphone impedance matching for optimum results from your favourite headphones. With the current interest in high quality headphones driven by the portable audio revolution, this is the right product to get the best from them. Until you try a good quality headphone amplifier in place of the headphone sockets on most portables and amplifiers (where they are, in most cases, an afterthought to increase the feature count) you do not realise what you are missing.

The circuit utilises twin high specification E/I transformers output that will drive any headphone load from 16 ohms to over 300 ohms depending on how the secondaries are configured, switched by DIP switches for easy re-configuration.. The HD3S is a single-ended design, with the power pentode wired up in triode configuration for that added purity, and is as quiet as a mouse.

External dimensions: W220 x D314 x H82mm. Weight 3.6kg


http://www.world-designs.co.uk/headphone%20amps.htm
http://www.world-designs.co.uk/index_ht ... _Sep14.pdf
Beyerdynamic T1 v1 | AKG K240DF | AKG K400 \\ VE Zen 2.0 | Myst Nail 2 | Spiral Ear 3-way Reference
Zigis Trīsstūris | Eufonika H16M
Tento PortaDAC 1866OCUB | Allo Digione Player
kvik

Brugeravatar
 
Indlæg: 4278
Tilmeldt: 28. jul 2011, 01:27
Geografisk sted: Norge

Re: Rør, hvis du tør - ALLNIC Audio

Indlægaf kvik » 30. jan 2014, 23:54

ALLNIC HPA-3000 GT ($4900)

ALLNIC HPA-3000 GT.png
ALLNIC HPA-3000 GT.png (578.07 KiB) Vist 18195 gange

The HPA-3000 GT is Allnic Audio’s stereo headphone amplifier, with an output transformer coupled. The HPA-3000 GT has a voltage gain of +28dB, and a maximum output of 3 watts. It works best with headphones having an impedance of from 30 to 600 ohms.

Features:
• High-quality, NOS tubes
• Pure Class A operation
• As are all Allnic Audio products, the HPA-3000 GT is fully RoHS (EU Reduction of Hazardous Substances regulation) compliant in construction and materials
• Headphone output: The HPA-3000 GT is equipped with two(2) headphone outputs ‘jack’ and two(2) XLR for(4) pin outputs. Each for low and high impedance
• Pre output: The HPA-3000 GT is equipped with one(1) pair of RCA pre outputs, whose impedance is around 10 ohms, this extremely low value means very powerful driving capability to next amplifier with the widest frequency ranges
• Volume control: The HPA-3000 GT’s volume control is the large knob in the center of front panel. It rotates clockwise (gain increased) and counterclockwise (gain reduced)

Specifications:
• Inputs: One (1) pair unbalanced (RCA), One (1) pair balanced (XLR)
• Headphone Output: Two (2) one-quarter inch (1/4”), Two (2) XLR
• Pre-out: Available
• Frequency Response: 20Hz ~ 20KHz (±0.3db)
• Voltage Gain: +28dB
• Optimum Headphone Impedance: Low under 50 ohms, High under 600 ohms
• Output Wattage: Three (3) watts
• Maximum Input Voltage: Ten (10) volts RMS
• THD(Total Harmonic Distortion): Less than 0.03% (1KHz, Out put 1V)
• S/ N Ratio: -63db (CCIR, 1KHz)
• Power Consumption: 48 Watts
• Tubes: 6EM7 X 2
• Fuse: AC 2A, 250V
• Dimensions: 240mm x 330mm x 175mm (W x D x H)
• Weight: Unpacked: 10 kg

http://allnicaudiocom.cafe24.com/?page_id=928
http://audiomentors.co.kr/shop/hpa-3000-gt/



ALLNIC HPA-5000 XL ($7500)

ALLNIC HPA-5000 XL.png
ALLNIC HPA-5000 XL.png (630.1 KiB) Vist 18195 gange

The HPA-5000 is Allnic Audio’s stereo Headphone Amplifier. The HPA-5000 is an Output Transformer-less (OTL) and Output Capacitor-less (OTC) amplifier design, utilizing a true balanced Positive-Negative cancellation circuit. The HPA-5000 has a voltage gain of +28dB, and a maximum output of 5 watts. It works best with headphones having an impedance of from 30 to 50 ohms.

A design made for the true headphone audiophile, a tubed output transformer-less, output capicitator-less design from the genius of KS Park. Kang Su has a passion for excellent headphone designs, he once heard a similar design in Japan at an audio show. He thought it showed good promise but felt the tubes and circuit employed could be designed from the ground up to make for a more beautiful sound. After many years of study and a special purchase of Mullard E180CC vintage tubes, the dream was realised. This product is so special, it was categorized under the 5000 series.

What you need to know about ALLNIC AUDIO: ALLNIC is short for “All Nickel” which comes from the fact that all our output transformers are made with 78 percent nickel core perm alloy. This not only makes ALLNIC a one of a kind, listeners hear more of the lows and highs with the greatest dynamic range available. With ALLNIC you can expect greater life expectancy from vacuum tubes as we use only New Old Stock Vacuum Tubes. Since they last longer you save money. We also employ our patented gel cap dampening tube sockets which isolate micro phonics eliminating unwanted external vibrations giving listeners the purest sound possible. The ALLNIC built 41 silver stepped motorized remote controlled volume attenuator provides precise volume tracking and ease of operation making it convenient and allowing more listening time. The convenience of being able to match any power tubes with our manual power tube bias feature will save a lot of money and time in the long run. Easy access to our surface mounted fuses for each power tube save you time, money and frustration. You can be confident in our performance with ALLNIC’s two year transferable warranty on electronics and one year transferrable warranty on tubes. Our warranty protects your investment at the same time increasing the resale value


Features:
• High-quality, NOS tubes
• True OTL/OCL design
• Pure Class A operation
• New vacuum tube damping technology – Allnic Audio’s patented "Absorb GEL tube damper" technology prevents harmful vibrations from reaching the driver tubes and, therefore, prevents micro-phonic noise propagation in the tubes. The Allnic Audio Absorb Gel damper technology effectively solves a problem that plagues most tube amplification systems. Provided other tube components do not introduce micro-phonic noise into your system, with the Absorb Gel damping system, you will enjoy a degree of transparent sound that will surprise and please you.
• As are all Allnic Audio products, the HPA-5000 is fully RoHS (EU Reduction of Hazardous Substances regulation) compliant in construction and materials

Specifications:
• Power Consumption: Tubes:
• Inputs: Two (2) pairs unbalanced (RCA)
• Headphone Output: One (1) one-quarter inch (1/4”)
• Frequency Response: 20Hz ~ 20KHz (±0.3db)
• Voltage Gain: +28dB
• Optimum Headphone Impedance: Thirty (30) to fifty (50) ohms
• Output Voltage: Five (5) watts
• Maximum Input Voltage: Five (5) volts RMS
• THD (Total Harmonic Distortion): Less than 0.03% (1KHz, Output 1V)
• S/N Ratio: -68db (CCIR, 1KHz)
• Power Consumptioin: 70 Watts
• Tubes:
6AN8 – New Old Stock – first gain stage – no equivalents
E180CC - New Old Stock - second gain stage - approximately electrically (not sonically) equivalent: CV8431, 7062, 5965, 12AV7, 6414, 6829
7233 – New Old Stock – no equivalents
• Fuse: AC 2A, 250V
• Dimensions: 230mm (~9.1 inches) x 380mm (~12.3 inches) x 165mm (~6.5 inches) (W x D x H)
• Weight: Unpacked: 9 Kg (~19.9 lbs), Packaged: 11 Kg (~24.26 lbs)

http://allnicaudiocom.cafe24.com/?page_id=1088
http://hammertoneaudio.com/product/hpa5000xl
Beyerdynamic T1 v1 | AKG K240DF | AKG K400 \\ VE Zen 2.0 | Myst Nail 2 | Spiral Ear 3-way Reference
Zigis Trīsstūris | Eufonika H16M
Tento PortaDAC 1866OCUB | Allo Digione Player
kvik

Brugeravatar
 
Indlæg: 4278
Tilmeldt: 28. jul 2011, 01:27
Geografisk sted: Norge

Re: Rør, hvis du tør - Vacuum Tube Audio

Indlægaf kvik » 1. feb 2014, 13:44

Vacuum Tube Audio HA12 ($1000)

Vacuum Tube Audio HA12.jpg
Vacuum Tube Audio HA12.jpg (73.7 KiB) Vist 10398 gange

The new HA12 headphone amplifier is the result of a custom headphone amp built for a customer, and this version is now offered for anyone interested. This circuit design has several refinements for hi-end performance. This includes include a tube rectified and choke filtered high voltage power supply, with regulation for the signal amplifier. The filament supply has 18800 uF of capacitance for very low noise and ripple. The amp uses two EL84 output tubes, one 12AX7 preamp tube, and one 6CA4 rectifier tube. The output signal is transformer coupled to a pair of low-Z (32-100 ohm) and hi-Z (200-600 ohm) headphone outputs. There are two inputs, and dual mono gain/balance attenuators, followed by your choice of an ALPs RK27 volume control or a 24 step precision volume attenuator. The high voltage to the 12AX7 signal amplifier is regulated for very low noise and separation from the power amp output. The signal thru the EL84 output tube goes thru a high quality polypropylene film capacitor to the impedance matching output transformer. Frequency response is measured to be flat from 10Hz to 40KHz. Output power is meaured to be 500mw into 32 ohms and 60mw into 300 ohms, equivilent to a 2 watt amplifier into 8 ohms. Purchase options: Basic PCB board kit with parts (no chassis, no tubes, no transformers) is $249; Complete kit of all parts to build is $790; Assembled, tested, ready to use HA12 headphone amp is $999.

http://tubes4hifi.com/HA12.htm



Vacuum Tube Audio HA-14 ($?)

Vacuum Tube Audio HA14.jpg
Vacuum Tube Audio HA14.jpg (95.7 KiB) Vist 10398 gange

This HA14 headphone amplifier was a custom design and build for a customer. Based on the schematic of an existing $800 product, we decided to do several upgrades to the basic design of the original for better sound and higher power output, using octal tubes rather than common noval tubes. These upgrades include choke filtered high voltage power supplies, with regulation for the signal amplifier. The result is more similar to products in the $1500-2000 range, with a completely dual mono design, using a pair of dual primary transformers as the only common element. Each channel has a 6X5GT tube rectifier with a CLC filter using a choke. There are two inputs, and dual mono gain/balance attenuators, followed by a very high quality TKD volume control. The high voltage to the 6SL7 signal amplifier is regulated for very low noise. The signal thru the 6L6GC output tube goes thru a high quality SoniCap to the impedance matching output transformer, with outputs for low-Z (32-100 ohm) and hi-Z (200-600 ohm) headphone outputs. Frequency response is measured to be flat from 10Hz to 40KHz. Output power is meaured to be 1000mw into 100 ohms, about 6 times as much as the original base design.

http://www.tubes4hifi.com/HA14.htm

The same circuit design but using more common and less expensive 9 pin tubes (12AX7, EL84, 6CA4) is our new HA12 headphone amp. All on one compact circuit board (7.2' x 5.4") and using a single power transformer. Available as basic kit, complete kit, or plug-in ready amp.



Custom Amps built to your specs!! Email for more info and a quote . . .
Another VTA custom headphone amp (HA-9)
Beyerdynamic T1 v1 | AKG K240DF | AKG K400 \\ VE Zen 2.0 | Myst Nail 2 | Spiral Ear 3-way Reference
Zigis Trīsstūris | Eufonika H16M
Tento PortaDAC 1866OCUB | Allo Digione Player
kvik

Brugeravatar
 
Indlæg: 4278
Tilmeldt: 28. jul 2011, 01:27
Geografisk sted: Norge

Re: Rør, hvis du tør - Laconic Lab

Indlægaf kvik » 1. feb 2014, 16:23

Laconic Lunch Box Pro ($195)

Laconic Lunch Box Pro.jpg
Laconic Lunch Box Pro.jpg (297.41 KiB) Vist 17713 gange

Laconic Lunch Box Pro HA-06 is designed for high quality amplification of the audio signal and pairing the line out signal source with headphones. The amplifier has an extended dynamic range compared to the base model HA-06T. Increased power output, increased supply capacity of the power supply. Improved components (capacitors). The design uses matched tubes. As the source, you can use sound cards for computers, CD/DVD players, and other devices with standard linear output.

Specifications:
• Frequency range: 10-100000 Hz
• S/N Ratio: -80 DB
• Gain: 16 DB
• Dynamic range: 100 dB (250 Ohm load)
• THD: < 0.15%
• Input voltage: 0.25-2.0 V
• Input impedance :10 kΩ (20 kΩ)
• Output impedance: 30 Ohm
• Headphone impedance: Low 32-150 Ohm, Hi 150-600 Ohm
• Output connector: Jack 6.3 mm (x1)
• Input connectors: RCA
• Power supply: Built-in
• Output voltage: 2-5 V
• Power consumption: 20 W
• Tubes: 6N3P, 2x 6N24P
• Dimensions: 160 x 65 x 130 mm
• Weight: 1300 g

http://laconiclab.ru/lunch_box_pro.html



Laconic Azur H2 ($260)

Laconic Azur H2.jpg
Laconic Azur H2.jpg (276.86 KiB) Vist 18195 gange

Laconic AZUR H2 amplifier designed for high gain tone and pairing linear output signal source with headphones have a resistance of 32 to 600 ohms. Laconic AZUR H2 has an expanded dynamic range while working load of 60-600 ohms. In the absence of the plug into the headphone amplifier performs the function of pre-amp (socket OUT). As the source is allowed to use the computer sound card, CD / DVD players and other devices that have a standard line output.

• Operating frequency range: 10-100000 (+ - 1dB)
• Gain: 15 dB
• The noise / background: < -85 dB
• Dynamic range (at load 250 Ohms): > 95 dB
• THD: < 0.5%
• Nom. input voltage: 0.25-2.0 V
• Load resistance: 32 - 600 Ohm
• Tubes: 1x 6N1P, 2x 6N6P
• Material: Steel
• Color: Black
• Dimensions: 170 x 100 x 130 mm
• Weight: 2 kg (without packaging)

http://laconiclab.ru/azur_h2.html



Laconic Night Blues Mini ($355)

Laconic Night Blues Mini.jpg
Laconic Night Blues Mini.jpg (122.47 KiB) Vist 17713 gange

2012 model year. Tube amplifier , developed based on the legendary Night Blues NB-3A V2. Reduction in size and weight copy " older brother " Night Blues NB-3A V2. Night Blues Mini is designed to work with any low-impedance load , which is the most difficult for tube amplifiers . The novelty lamps are used , originally developed for audio applications - this is the input and the output light 6ZH1P 6N24P . The amplifier used for headphones specially designed low-noise power supply circuit . Night Blues Mini features high output power and can also work well with high- headphones. For this there are two ways , for low resistance and high impedance headphones.

• Outputs: 2x 6.3 mm
• Frequency range:10 - 30000 Hz
• Inputs: 1x RCA
• Distortion: 1%
• Dimensions: 190x170x100 mm
• Weight: 2 kg

http://laconiclab.ru/laconic_night_blues_mini.html



Laconic ZD Mini ($370)

Laconic ZD Mini.jpg
Laconic ZD Mini.jpg (123.06 KiB) Vist 17713 gange

The amplifier is for high-quality audio signal amplification and coupling line-out signal source with headphones with resistance from 32 up to 600 ohms. The amplifier has an extended dynamic range when working with load 32-600 ohms. As the source, you can use sound cards for computers, CD/DVD players, as well as devices with standard linear output.Diagram courtesy of Edde Curent and used with their consent.

Specifications
• Driver tube: 6N9S (equivalent to 6SL7 , 6Sl7G, 6SL7GT, 1579)
• Power tube: 6N13S (equivalent to 6N5S, 6AS7, 6080.7802)
• Frequency range: 10Hz-100kHz 1dB (headphone 150-600 ohm)
• Gain: 18 dB (8 times)
• SNR: -95dB
• Headphone impedance: 32-600 Ohm
• Dynamic range: > 80dB (250 Ohm load)
• THD: < 0.5%
• Nominal input voltage 0.25-0.2 V
• Dimensions in mm (WxHxD) 125 x 180 x 290 (320 with volume controls and RCA connectors

http://laconiclab.ru/laconic-zd-mini.html



Laconic Night Blues NB-3A ($485)

Laconic Night Blues NB-3A.jpg
Laconic Night Blues NB-3A.jpg (239.62 KiB) Vist 18195 gange

2012 model year. Universal tube amplifier designed for low impedance and high-resistance load. Has a transformer output , which makes it possible to get the highest quality sound. The novelty lamps are used , originally developed for audio applications - this is the input and the output light 6N8S 6P6S . The amplifier used for headphones specially designed low-noise power supply circuit . NB-3A features high output power and can be operated with high- headphones. For this there are two ways , for low resistance and high impedance headphones. Night Blues, not being a hybrid, combining the advantages of the transistor and tube amp , being all-tube , nevertheless amplifier can work effectively with low-impedance load.

• Frequency range: 12-35000 ( + - 1 dB)
• Noise/background: < 87 dB
• Gain: 12 dB
• Dynamic range (with a load of 24-600 Ohm): > 95 dB
• THD: < 0.5%
• Input voltage: 0.3-3,0 V
• Load resistance 24-600 Ohm
• Outputs: 2x headphone jack 6.3mm
• Inputs: 1x line-in RCA
• Tubes: 2x 6N8S, 2x 6P6S
• Material: Steel
• Color: Black
• Size WHD: 195x135x250 mm
• Product/Shipping weight: 4.8/6.0 kg
• Warranty: 1 year

http://laconiclab.ru/laconic_night_blues.html
Beyerdynamic T1 v1 | AKG K240DF | AKG K400 \\ VE Zen 2.0 | Myst Nail 2 | Spiral Ear 3-way Reference
Zigis Trīsstūris | Eufonika H16M
Tento PortaDAC 1866OCUB | Allo Digione Player
kvik

Brugeravatar
 
Indlæg: 4278
Tilmeldt: 28. jul 2011, 01:27
Geografisk sted: Norge

Re: Rør, hvis du tør - ZMF

Indlægaf kvik » 2. feb 2014, 22:23

ZMF Pendant ($2000)

ZMF Pendant.jpg
ZMF Pendant.jpg (457.8 KiB) Vist 12230 gange

Pendant: an artistic and musical component intended to match and complement.

ZMF Pendant.. The only tube amp you’d ever need for full sized dynamic and planar headphones, as well as portables and even IEM’s! Yes - it’s THAT quiet!

Pendant was designed in collaboration with ampsandsound.com to make a headphone amp that not only perfectly matches any ZMF, but also any headphone on the planet. Pendant has the right size and capability to be your only headphone amp. Utilizing the 12au/t/x7 tubes, the Pendant outputs 30, 70, or 100 percent (respectively) of its gain based on the tube used for the optimal output for any headphone, along with the ability to use the entire volume knob range if desired.


• EL84 drivers, 12au/t/x7 input, 6CA4 rectifier tubes
• High and Low-Z outputs. 8 ohms and 300 ohms for use with virtually any high end headphone
• 2.5 Watts @ 8 ohms & 1.5 Watts @ 300 ohm
• Matte Black or custom wood chassis (base)
• Custom choke for dead quiet sound reproduction
• Optional vintage tube set: EL84 / 6CA4 / 12au7, 12at7 and 12ax7 (NOTE: Vintage ubes may include a variety of tubes that are picked by us to get the best sound possible from your Pendant.)

http://www.zmfheadphones.com/ampsanddacs/zmf-pendant
https://www.superbestaudiofriends.org/i ... rder.6607/
Beyerdynamic T1 v1 | AKG K240DF | AKG K400 \\ VE Zen 2.0 | Myst Nail 2 | Spiral Ear 3-way Reference
Zigis Trīsstūris | Eufonika H16M
Tento PortaDAC 1866OCUB | Allo Digione Player
kvik

Brugeravatar
 
Indlæg: 4278
Tilmeldt: 28. jul 2011, 01:27
Geografisk sted: Norge

Re: Rør, hvis du tør - Monoprice

Indlægaf kvik » 2. feb 2014, 22:27

Monolith Tube Headphone Amplifier ($400)

Monolith Tube HPA.jpg
Monolith Tube HPA.jpg (268 KiB) Vist 12790 gange

The Monolith™ Tube Headphone amplifier brings out the best in your headphones with the rich, warm sound of vacuum tube power. Featuring a powerful 6N5P tube and dual 6N3 tubes, the Monolith Tube Headphone Amplifier will effortlessly drive the most demanding headphones. Upgrade the sound from your computer with the internal 32-bit 384kHz ESS Sabre® DAC. Connect your PC or other digital playback device and bring your listening experience to a new level with the ESS Sabre DAC combined with the warm analog sound of vacuum tubes.

Tube Sound.. The Monolith™ Headphone Tube Amplifier utilizes a powerful 6N5P dual triode tube coupled with an output transformer for the output stage. Many competing designs only utilize a large electrolytic capacitor on the output, which degrades sound quality. Dual 6N3 tubes are utilized for the input stage and can cross over to US equivalents 2C51 or 396a. The 6N5P crosses over to a US6080 or 6AS7.

ESS Technology,, The ESS ES9018 Sabre® chip uses the patented 32-bit HyperStream™ DAC architecture and Time Domain Jitter Eliminator to bring out the best in your digital recordings. The USB receiver is the Savitech SA9227. It supports all sample rates up to 384kHz/32-bit and is clocked by two onboard oscillators.

Impedance Selector.. Optimize performance for your headphones! The impedance selector allows you to perfectly match the amplifier to the headphone impedance, ensuring that the ideal power is being utilized for any pair of headphones. The impedance can be set to one of five impedance groups, from 16 to 600 ohms.


Specifications
• Input Stage Tube Type: 2x 6N3 (crossing over to US equivalents 2C51 or 396a)
• Output Stage Tube Type: 6N5P (crossing over to US equivalents US6080 or 6AS7)
• Output Power (RMS): [email protected] / [email protected] / [email protected] / [email protected] / [email protected] (W/channel @ ohms)
• Inputs: Line-In 3.5mm (front), Line-In RCA (back), USB Type-B (back)
• Outputs: Headphone 6.35mm (front), Pre-Out RCA (back)
• Headphone Impedances: Selectable 16-32 / 33-64 / 65-150 /151-300 / 600 ohms
• DAC Chipset: ESS Sabre® ES9018S [email protected] and [email protected]
• USB Receiver Chipset: Savitech SA9227
• Direct Stream Digital™: DSD64, DSD128, and DSD256
• Frequency Response: 20Hz ~ 20kHz (-1dB)
• Signal-to-Noise Ratio: ≤ 98dB (A weighted)
• Total Harmonic Distortion; < 1% @64 ohms
• Dimensions; 5.9” x 9.4" x 12.8" (150 x 240 x 325 mm)
• Weight: 20.5 lbs. (9.3 kg)

https://www.monoprice.com/product?c_id= ... 1&format=2



Monolith Liquid Platinum ($800)

Monolith Liquid Platinum.jpg
Monolith Liquid Platinum.jpg (210.65 KiB) Vist 12790 gange

Monolith Liquid Platinum Headphone Amplifier by Alex Cavalli

The Cavalli/Monolith Liquid Platinum is a balanced version of the very highly regarded Cavalli Audio Liquid Crimson amplifier. The Platinum is fully balanced/differential amplification with 3.6W ( per channel balanced) into 50R. As an embedded tube hybrid (pioneered by Cavalli) the Platinum gives you the beautiful sound of tubes together with the grunt of solid state to drive the headphones. With multiple inputs and outputs for balanced and single ended operation, switchable gain, and easy front panel input selection, the Liquid Platinum will bring your music listening to new heights.


Specifications
• Frequency Response: 10Hz-50kHz ±0.05dB
• Included Tubes: 2x Electro Harmonix 6922
• Output Power (BAL/SE): 6.62/[email protected]Ω; 4.21/[email protected]Ω; 1.74/[email protected]Ω; 0.91/[email protected]Ω
• THD+N @1kHz w/47R Load Balanced Input: 1 Vrms: 0.0020% THD+N @ 1kHz; 5 Vrms: 0.0020% THD+N @ 1kHz
• IMD CCIF w/47R Load Balanced Input: 1 Vrms: 0.0006%; 5 Vrms: 0.0015%
• IMD SMPTE w/47R Load Balanced Input: 1 Vrms: 0.0006%
• Gain: 14dB (5x)
• Noise: -98dB (Balanced); -89dB (Single Ended)
• Crosstalk w/47R Load Balanced Input: -88dB
• Channel Balance: 0.3dB
• Output Impedance: < 0.14 Ohms Balanced; < 0.07 Ohms Unbalanced
• Headphone Outputs: 4 Pin XLR (Balanced), 1/4" TRS (Single Ended)
• Audio Output: Unbalanced RCA
• Audio Inputs: 3 Pin XLR Balanced, Unbalanced RCA Single Ended (converted to balanced internally)
• Dimensions: 8.8" x 8.5" x 2.0" (222 x 216 x 51 mm)
• Weight: 3.2 lbs. (1.5 kg)

https://www.monoprice.com/product?c_id= ... k2-2917105
https://www.head-fi.org/threads/monopri ... li.876406/
Beyerdynamic T1 v1 | AKG K240DF | AKG K400 \\ VE Zen 2.0 | Myst Nail 2 | Spiral Ear 3-way Reference
Zigis Trīsstūris | Eufonika H16M
Tento PortaDAC 1866OCUB | Allo Digione Player
kvik

Brugeravatar
 
Indlæg: 4278
Tilmeldt: 28. jul 2011, 01:27
Geografisk sted: Norge

Re: Rør, hvis du tør

Indlægaf Ole » 3. feb 2014, 21:17

Super arbejde, der er rigtig mange flotte forstærkere - men nogle af dem ved de også godt hvad de vil have for. Men man bliver jo næsten fristet :-)
Ω Heed Obelisk DA | Stello U3 | Stax SRM-323S | Stax SR-L700MKI
Ω AudioQuest Dragonfly Cobalt | Etymotic ER-4S
Ole

Brugeravatar
 
Indlæg: 395
Tilmeldt: 6. feb 2012, 19:50
Geografisk sted: Kolding

Re: Rør, hvis du tør - TPaudio

Indlægaf kvik » 5. feb 2014, 20:51

TPaudio CF-OTL (€190)

TPaudio CF-OTL.jpg
TPaudio CF-OTL.jpg (64.06 KiB) Vist 18195 gange
TPaudio CF-TOR.jpg
TPaudio CF-TOR.jpg (39.33 KiB) Vist 18195 gange

For headphones between 30 and 600 ohm. Usable alone, or inserted between CD-player and amplifier, or beween pre-amp and power amplifier. Does not negatively influence the signal path. Gold plated RCA input and output connectors. 6.3 mm headphone jack. Cabinet in brushed stainless steel, side panels in solid cherry .

• High Level Inputs: CD
• Sensitivity input: 250 mV
• Input impedance: 100 Kohm
• Output impedance: For 30 to 600 ohm headphones
• Output power of 0.7 watts per channel
• Frequency Response: 35Hz - 50,000 Hz + - 1.5 dB
• S/N Ratio: 90dB
• Operation: Class A + SRPP
• Standard valves: 1x ECC82/12AU7, 2x ECC88 (replaceable with ECC88/6DJ8/6922/6N1P/6N23P)
• Component assembly: Power Supply - PRINTED / Audio Section - POINT TO POINT
• Dimensions (WDH): 24 x 19 x 14 cm
• Weight 2.5 kg

On request with ALPS Blue potentiometer
Can be also be delivered as transformer coupled

http://www.tpaudio.it/cf-otl/



TPaudio CF-4T-OTL (€240)

TPaudio CF-4T-OTL.jpg
TPaudio CF-4T-OTL.jpg (54.55 KiB) Vist 18195 gange
TPaudio CF-4T-TOR.jpg
TPaudio CF-4T-TOR.jpg (119.95 KiB) Vist 18195 gange

For headphones between 30 and 600 ohm. Usable alone, or inserted between CD-player and amplifier, or beween pre-amp and power amplifier. Does not negatively influence the signal path. Gold plated RCA input and output connectors. 6.3 mm headphone jack. Cabinet in brushed stainless steel, side panels in solid ash or cherry .

• High Level Inputs: CD
• Sensitivity 'input: 250 mV
• Input impedance: 100 Kohm
• Output impedance: For 30 to 600 ohm headphones
• Output power of 0.7 watts per channel
• Frequency Response: 30Hz -80 000 Hz + - 1.5 dB
• S/N Ratio: 90dB
• Operation: Class A + SRPP
• Standard valves: 2x EC86, 2x ECC88 (replaceable with 6N1P/E88CC/6DJ8/6N23P)
• Component assembly: Power Supply - PRINTED / Audio Section - POINT TO POINT
• Dimensions (WDH): 24 x 19 x 14 cm
• Weight 2.5 kg

On request with ALPS Blue potentiometer
Can be also be delivered as transformer coupled

http://www.tpaudio.it/cf-4t-otl/



TPaudio CF-OTL6080 V2.0 (€350)

CF-OTL6080 V2.0.jpg
CF-OTL6080 V2.0.jpg (462.83 KiB) Vist 3750 gange

• High Level Inputs: CD
• Sensitivity input: 250 mV
• Input impedance: 100 Kohm
• Output impedance: For 30 to 600 ohm headphones
• Output power of 1.8 watts rms per channel
• Frequency Response: 25 Hz to 100,000 + -1.5 dB
• S / N Ratio -90 dB
• Headphone Jack: XLR-4-pin JACK
• Operation: Class A + SRPP
• Standard valves: 2x EC86, 2x 6AS7-6080
• Component assembly: Power Supply - POINT TO POINT / Audio Section - POINT TO POINT
• Silver aluminum enclosure, side panels in solid beech or mahogany
• Dimensions (WDH): 26 x 35 x 16 cm
• Weight 6 kg

On request with ALPS Blue potentiometer

http://www.tpaudio.it/cf-otl6080/
https://www.facebook.com/tpaudio/



Custom Orders

TPaudio Custom Built 1.jpg
TPaudio Custom Built 1.jpg (35.14 KiB) Vist 18195 gange
TPaudio Custom Built 2.jpg
TPaudio Custom Built 2.jpg (74.63 KiB) Vist 18195 gange
TPaudio Custom Built 3.jpg
TPaudio Custom Built 3.jpg (93.16 KiB) Vist 18195 gange
Senest rettet af kvik 13. feb 2014, 12:39, rettet i alt 1 gang.
Beyerdynamic T1 v1 | AKG K240DF | AKG K400 \\ VE Zen 2.0 | Myst Nail 2 | Spiral Ear 3-way Reference
Zigis Trīsstūris | Eufonika H16M
Tento PortaDAC 1866OCUB | Allo Digione Player
kvik

Brugeravatar
 
Indlæg: 4278
Tilmeldt: 28. jul 2011, 01:27
Geografisk sted: Norge

Re: Rør, hvis du tør - S.I. Audio

Indlægaf kvik » 9. feb 2014, 00:54

S.I. Audio Intimo MK2 (€2950)

S.I. Audio Intimo MK2.jpg
S.I. Audio Intimo MK2.jpg (469.19 KiB) Vist 18195 gange

"Intimo" will give you unforgettable listening sessions, full of detail and musicality thanks to the OTL technology; and with record-breaking silence for an "All Tubes".

Great versatility: it can be combined with the vast majority of headphones on the market; once yours, it will be really difficult to part with it!

And thanks to the possibility of using up to two headphones at the same time, you can also make direct comparisons between headphones, or share your music with another enthusiast.


Features
• 2× 1 Watt RMS
• Designed for 8 to 600 ohm headphones
• Quiet operation. Low distortion and correct spectrum.
• Automatic optimization of the operating point of the power tubes throughout their lifespan.
• Triodes in all aspects of amplification, including the output stage.
• Two chassis. Separate tube power supply. Completely dual mono.
• Total absence of feedback.
• Up to two headphones can be used simultaneously (6.3mm Jack)
• Headphone handling optimized to reduce distortion and extend bandwidth
• Matched and selected power tubes particularly suitable for OTL and SRPP circuits: reliability, long life, easy future availability
• 2 power transformers, designed for audio use, according to CE/ISO standards with total power over 200 VA – primary/secondary shield to eliminate network interference
• Printed circuit boards with double thickness tracks - low loss fiberglass dielectric
• Passive components from leading brands

Specifications
• Frequency response: 2-100.000 hz +/- 1dB
• THD: 0.1%
• S/N ratio: 106 dB
• Inputs: 1 RCA/XLR Line
• Outputs: Unbalanced 2x Jack 6.3mm; Balanced 2x XLR (right channel and left channel)
• Load impedance 8-600 ohm
• Input impedance: 47Kohm
• Sensitivity: 250mV
• Tube complement: 2x ECC82; 4x 6H30; 2x 6L6GC
• Finish: Wood or Plex
• Dimensions (WxDxH): Amplifier 34.5x30x15.5cm; Power supply 23.5x28x10cm
• Optional: Balanced floating input €250

http://www.siaudio.it/prodottisiaudio/intimo-mk2/
Beyerdynamic T1 v1 | AKG K240DF | AKG K400 \\ VE Zen 2.0 | Myst Nail 2 | Spiral Ear 3-way Reference
Zigis Trīsstūris | Eufonika H16M
Tento PortaDAC 1866OCUB | Allo Digione Player
kvik

Brugeravatar
 
Indlæg: 4278
Tilmeldt: 28. jul 2011, 01:27
Geografisk sted: Norge

Re: Rør, hvis du tør - ARG.audio

Indlægaf kvik » 9. feb 2014, 02:05

ARG.audio DYANA 645 SE

ARG.audio DYANA 645 SE.jpg
ARG.audio DYANA 645 SE.jpg (39.13 KiB) Vist 17674 gange

A Monotriode.. Why a monotriode? A low power single-ended tube, combined with high efficiency loudspeakers, allow the achievement of a very particular sound realism in itself, full of consistency, transparency and with a dynamic really unthinkable without listening fatigue.

The Diana 645 SE has its strength in manufacturing simplicity (few components, but good and above all used well!), has no negative feedback, even local!! Has no passive component (resistor, capacitor ...) in the signal path that can introduce colorations or distortions, except a resistor on the grid (Kiwame non-inductive).


Specifications
• Max. Power: 1,5 Wrms
• Tubes: 2x 6C45P-I
• Total harmonic distortion (THD unweighted): 0,015% 20Hz-20kHz
• THD max: < 0,6%
• Input impedance: 47 kOhm
• Frequency response: 20Hz-75kHz ±2dB
• Output impedance: 16, 25, 32 Ohm
• AC: 230V
• Weight: 13kg

http://www.argaudio.it/dyana-se645.html
Beyerdynamic T1 v1 | AKG K240DF | AKG K400 \\ VE Zen 2.0 | Myst Nail 2 | Spiral Ear 3-way Reference
Zigis Trīsstūris | Eufonika H16M
Tento PortaDAC 1866OCUB | Allo Digione Player
kvik

Brugeravatar
 
Indlæg: 4278
Tilmeldt: 28. jul 2011, 01:27
Geografisk sted: Norge

Re: Rør, hvis du tør - Sophia Electric

Indlægaf kvik » 9. feb 2014, 02:08

Sophia Electric Baby Amplifier II ($1400)

Sophia Electric Baby Amp II.jpg
Sophia Electric Baby Amp II.jpg (427.53 KiB) Vist 17674 gange

Sophia Electric single ended integrated Baby Amplifier delivers 5 watts per channel x 2 of glorious lush magical sound, exceptional wide bandwidth, resolution and dynamics. More powerful than typical 2A3 single ended amplifiers. It can drive Sophia Electric made Model One(88dB) and Model Two speakers(88 dB) nicely in a typical home setting or in an office.

Retail Price $999.99

Optional headphone amplifier function is being built on custom order at $399.99 extra, perfect for high impedance headphones HD600, HD650, Hifiman HE600 as well as low impedance Grado 125, Philips 9500, and Sony headphones. All above mentioned headphone models have been tested. Other headphones with similar impedance characters should work as well.

This single ended Baby headphone amplifier has transformer output, so the sonic performance is light-years ahead of those entry level headphone amplifiers that do not have transformer output.

Since 2001, Sophia Electric Baby Amplifier has built a track record for Audiophile sonic performance and superior reliability. This new single ended Baby amplifier is expected to be a winner as well.



Specifications
• Power: 5 watts x 2 single ended class A circuit
• Input: Two pairs of RCA inputs (CD and AUX)
• Output: Mil Grade 6P1T x 2
• Input/Driver tube: NOS 6J1 x 2
• Frequency: 12Hz-40KHz
• Hum: 1mv or less
• Weight: 20 pounds
• AC Power: 120V/60Hz or 235V/50Hz
• Required break in time: 50-100 hours
• Warranty: One year parts and labor, Sophia electric brand tubes one year, Non-Sophia Electric tubes 6 month


http://www.sophiaelectric.com/pages/amp/Baby_SE_II.htm
Beyerdynamic T1 v1 | AKG K240DF | AKG K400 \\ VE Zen 2.0 | Myst Nail 2 | Spiral Ear 3-way Reference
Zigis Trīsstūris | Eufonika H16M
Tento PortaDAC 1866OCUB | Allo Digione Player
kvik

Brugeravatar
 
Indlæg: 4278
Tilmeldt: 28. jul 2011, 01:27
Geografisk sted: Norge

ForegåendeNæste

Tilbage til Hovedtelefon forstærkere

Hvem er online

Brugere der læser dette forum: Ingen tilmeldte og 0 gæster

cron